Dacor RNHP4812S Instalační manuál

Installation InstructionsRenaissance® Wall Mount Range HoodsModels RNHP30, RNHP36, and RNHP48Part No. 109172 Rev. AAPPROVED FOR USE WITH ALL DACOR® R

8 WARNINGTo reduce the risk of personal injury caused by reaching over a hot appliance, cabinet storage space located directly above the range should

9Preparation and SetupThe blower direction is through top A of the hood. However, the blower can be rotated to vent through the rear B of the ho

10• The hood exhaust connects to an 8-inch round duct. You can increase the duct size over the duct run if desired. • To prevent a backdraft, never

11Preparation and SetupPreparing the Mounting LocationHolding brackets and hardware are provided to temporarily hold the hood in place while you perma

12Rear Exhaust CenterlineTop Exhaust CenterlineThese measurements and marks are for centering and leveling the hood, marking the duct cutouts, and ins

13Installing the Holding BracketsIMPORTANT: Placing the holding brackets above, below, or off the centerline will cause alignment problems during fina

14The blowers (also called fans) can be rotated so that the air is vented out the back of the hood. If the hood will be installed in a top exhaust con

15Various models illustrate these instructions, so the images presented might not be an exact replication of the hood being installed.However, the bes

16Back of HoodDefault Orientation:Top Vent OpenRear Vent ClosedTop of HoodBlower/VentL-BracketInstallation InstructionsStep 9Rotating the Blower(s) fo

17Installation InstructionsStep 15Blower I/O portBack of HoodFront of HoodTop of HoodBack of HoodRotating the Blower(s) for Rear ExhaustOrientating th

Planning the Ductwork ... 9Preparing the Mounting Location ...11Ins

18Installation InstructionsAssembling the FiltersFilters are boxed separately and must be assembled during installation. All knobs and hardware that i

19Installation InstructionsFour (4) corners are bent backward 90 degrees.Using the Dual to Single Transition Kit# AHT10On dual exhaust models, the two

20Long edge on top of kit is straight and unbent. It overlaps the top of the hood and works like a bracket.Installing the AHT10Top Vent: 3012, 3612, 4

21Installation InstructionsHanging the Range Hood WARNINGHanging the range hood requires two people. Do not attempt to lift the hood without assistanc

22Installation InstructionsGREENGREENWHITEWHITEBLACKBLACKJunction Box Wire DiagramUL/CSA approved NEMA strain reliefTo house circuit breaker or fuse

23Installation Instructions WARNING• Do not ground the circuit to a gas line.• Do not ground the circuit to a hot water pipe.• Water lines that are

24Verifying the Setup1. Make sure the main power switch is OFF. (Refer to the figures at right.)2. Turn power ON at the circuit panel or fuse box.3.

25The Installation Checklist WARNING• To ensure a safe and correct installation, the follow-ing checklist should be completed by the installer to ens

26Wiring DiagramsRNHP3012, RNHP3018NOCOMCOILBBLWRYYW WPOWERSWITCHCONNECT TO120V, 60Hz, 15ASINGLE PHASEPOWER SUPPLYBBBBGWW GCHASSISGROUNDBLOWER455W, 11

27Wiring DiagramsRNHP3612, RNHP3618NOCOMCOILBWRYYYW WWPOWERSWITCHCONNECT TO120V, 60Hz, 15ASINGLE PHASEPOWER SUPPLYBBBBGWW GCHASSISGROUNDBLOWER455W,

1Important Information About Safety Instructions• The Important Safety Instructions and warnings in these instructions are not meant to cover all pos

28Wiring DiagramsRNHP4812, RNHP4818NOCOMCOILBBLORWBBLORWOWRYYYW WWBLOWER455W, 115VPOWERSWITCHCONNECT TO120V, 60Hz, 15ASINGLE PHASEPOWER SUPPLYBBBBGWW

29Notes

Dacor ● 14425 Clark Avenue, City of Industry, CA 91745 ● Phone: (800) 793-0093 ● Fax: (626) 403-3130 ● www.dacor.com

2Important Safety Instructions• Do not install or operate this hood if it has been damaged, dropped, has damaged electrical wires or is not working p

3General SpecificationsAll ModelsFeatures DescriptionBlower SpeedsFour (4)Filters Baffle style, dishwasher safeExhaust(s) 8-inch duct diameterTotal Co

4DimensionsProduct SpecificationsModels RNHP48 Models RNHP36 & RNHP30* ** Electrical and Ductwork ConnectionsTolerances: +1/16” -0”, unless o

5Product SpecificationsDimensionsTolerances: +1/16” -0” unless otherwise stated.Single Blower: RNHP30 & RNHP36 SeriesDual Blower: Model RNHP48 Ser

6Preparation and SetupParts ListBADCBECFGGIFSTAINLESSSTEELCLEANERDIAEHood InstallationPhillips screwdriver Drill + bits JigsawFlathead screwdriverTape

7Preparation and Setup Installing the Electrical Source WARNINGMake sure electrical service to the range hood is installed by a licensed electrician.I